#Rpi.gpio python library reference serial
#Rpi.gpio python library reference software
#Rpi.gpio python library reference license

The Functions page lists and documents whatРІР‚в„ўs available, andР”Р„dditional information can be found on the Raspberry Pi Wiki pages.

See the pins page for a description of the WiringPi pin to GPIO connector mappings, and take note of theРІР‚В¦.The gpio program can be used to control the GPIO pins in its own right, allowing easy testing of the GPIO interface from the command-line or simple shell scripts. This program is a set-uid program and can be run as a normal user. WiringPi normally uses a very low-level mechanism to access the underlying hardware РІР‚вЂњ this results in very fast access, however the down-side is that your programs need to be run as root, so in addition to this, wiringPi has the ability to use the traditional /sys/class/gpio/ style interface, and if the GPIO pins have been exported and had their ownership changed appropriately, then applications using the wiringPi library, can be run without root privileges.Р”Р„ supporting program, gpio, allows you to export and unexport the devices through the /sys/class/gpio/ interface. Using the wiringPi pin numbering scheme caters for these changes and progams will run un-changed on their board revision. Note that when using the BCM_GPIO numbering scheme, you must take into account the board revision! Some pins changed their meaning and numbers from revision 1 to revision 2.WiringPi supports both an Arduino style pin numbering scheme which numbers the pins sequentially from 0 upwards, as well as the Raspberry PiРІР‚в„ўs native BCM_GPIO pin numbering scheme. An implementation in Node by Igor Soarez.Pi4J is another Java project that uses WiringPi.Thanks to Dave Boulton for creating a TCL wrapper which can be found here.Thanks to Jeroen Kransen there are wrappers for Java which can be found here.Thanks to Gadgetoid there are now wrappers for Ruby, Python and Perl and these can all be found here.WiringPi fully supports the PiFace board too.

#Rpi.gpio python library reference serial

Serial port handling (both on-board and USB).

You can use this to read and write the pins and even use it to control them from shell scripts. WiringPi includes a command-line utility gpio which can be used to program and setup the GPIO pins. The I2C and SPI interfaces can also be used a general purpose I/O pins when not being used in their bus modes, and the UART pins can also be used if you reboot with the serial console disabled, giving a grand total of 8 + 2 + 5 + 2 = 17 I/O pins. The Revision 2 Raspberry Pi has an additional 4 GPIO lines on a separate connector which you have to solder onto the board. Additionally there is a 2-wire I2C interface and a 4-wire SPI interface (with a 2nd select line, making it 5 pins in total) and the serial UART with a further 2 pins. One of these pins can be designated for PWM output too. There are 8 general purpose digital I/O pins РІР‚вЂњ these can be programmed as either digital outputs or inputs. The Raspberry Pi has a 26-pin General Purpose Input/Output (GPIO) connector and this carries a set of signals and buses. Wiring is the core of the input and output for the Arduino, so I thought it would be good to replicate that functionality (or a good usable subset) on the Raspberry Pi.

#Rpi.gpio python library reference software

You may be familiar with the ArduinoРІР‚В¦ Briefly Arduino is really two things one is a hardware platform, the other software, and part of the software is a package called Wiring.

#Rpi.gpio python library reference license

WiringPi is an Arduino wiring-like library written in C and released under the GNU LGPLv3 license which is usable from C and C++ and many other languages with suitable wrappers (See below) IРІР‚в„ўd encourage you to use the new site if possible where there will be a forum and wiki (when I get time to implement them!) Most of the documentation on the projects site has been copied over to it the new site, but there may still be 1 or 2 pages that are still missing. WiringPi version 2 has been released and now has its own website ( ) to look after it.